surelyuknow
Tyme Master Jr.
- Joined
- Aug 5, 2014
- Messages
- 16,423
So its been awhile since I bought a new watch, more like 2 years I think, and I’m getting a little bit of an inch for something new but I’m not wanting to invest in another watch. (I have way too many as it is) So that leaves me with only one option… MOD one I already have. I decided to do a bracelet MOD on my 1986 Seiko 7002 Diver. It’s the perfect candidate for this particular bracelet. The one and only… Uncle Seiko Razor Wire bracelet. This bracelet is a near flawless match with great fit and finish, scissor type fold over clasp with push button release and fold over lock. Bracelet is extremely comfortable and doesn't pull any arm hairs. Only down side is the non-solid end links. Aside from that, I couldn’t be happier… at least with the end result. Getting there was a nightmare for me.
First off I couldn’t remove the old original rubber strap. I broke off 2 spring bar tool ends trying to get to and release the spring bars. I must have worked on it for a good half hour. Finally my patients wore thin and I had to go to plan B which involved some drastic measures. Cutting the b____ off. I got out my small dykes (yeah, I know probably politically incorrect but I don’t care as that’s what I always called them. Millennials stop your damn whining for gods sake. Man the hell up!) or side cutters as some folks call them. Anyway after removing the aforementioned but now useless strap you would think I would be home free. You my friend would be wrong… The friggin’ 33 year old spring bars were locked tighter than my ex-wife's…. hmmm, ahhhhhh pocketbook. Anyway I couldn’t get them off using 3 different kinds of spring bar tools. Back to plan B. Using my small needle nose pliers I finally just broke them off. Pictures to follow.
Ok, now I’m in the money. I just need to size this bad boy and I’m golden… or so you would seemingly think. Yeah, not so much! I knew ahead of time the links were not your usual easy to remove screw in or push pin type. I hadn’t expected them to be the Rubik’s Cube of bracelet links.
Warning: If you have shaky hands or poor eye sight do not attempt as this will cause you to re-think you hobby choices!
You will need very steady hands, a safety pin (easier to hold than a straight pin) and pointy tweezers. This does use push pins in the links but lining up those small razor wire links will drive you to drink (as seen in the picture below) and a whole lot of cussing. SOB, I mean lots and lots of cussing. In my dazed and confused state I think it took close to an hour to get this brace size. Mind you, you never get the correct amount of links off on the first try. You remove a couple of friggin’ links then put it all back together, slip it on your wrist just to find out… “Oh HELL NO! I’ve got to do this all over again!!!” So you go back and get another drink, just to steady your nerves mind you, and start the process all over. Finally you get it squared away and fitting just right and all’s well with the universe again. You then take that last swig of your drink, take your glasses off and lie down on the couch for a much needed and deserved nap…
Ok, so if you stuck with me thus far here are some pics. You decide… was it worth it?
Thanks for checking this out...
First off I couldn’t remove the old original rubber strap. I broke off 2 spring bar tool ends trying to get to and release the spring bars. I must have worked on it for a good half hour. Finally my patients wore thin and I had to go to plan B which involved some drastic measures. Cutting the b____ off. I got out my small dykes (yeah, I know probably politically incorrect but I don’t care as that’s what I always called them. Millennials stop your damn whining for gods sake. Man the hell up!) or side cutters as some folks call them. Anyway after removing the aforementioned but now useless strap you would think I would be home free. You my friend would be wrong… The friggin’ 33 year old spring bars were locked tighter than my ex-wife's…. hmmm, ahhhhhh pocketbook. Anyway I couldn’t get them off using 3 different kinds of spring bar tools. Back to plan B. Using my small needle nose pliers I finally just broke them off. Pictures to follow.
Ok, now I’m in the money. I just need to size this bad boy and I’m golden… or so you would seemingly think. Yeah, not so much! I knew ahead of time the links were not your usual easy to remove screw in or push pin type. I hadn’t expected them to be the Rubik’s Cube of bracelet links.
Warning: If you have shaky hands or poor eye sight do not attempt as this will cause you to re-think you hobby choices!
You will need very steady hands, a safety pin (easier to hold than a straight pin) and pointy tweezers. This does use push pins in the links but lining up those small razor wire links will drive you to drink (as seen in the picture below) and a whole lot of cussing. SOB, I mean lots and lots of cussing. In my dazed and confused state I think it took close to an hour to get this brace size. Mind you, you never get the correct amount of links off on the first try. You remove a couple of friggin’ links then put it all back together, slip it on your wrist just to find out… “Oh HELL NO! I’ve got to do this all over again!!!” So you go back and get another drink, just to steady your nerves mind you, and start the process all over. Finally you get it squared away and fitting just right and all’s well with the universe again. You then take that last swig of your drink, take your glasses off and lie down on the couch for a much needed and deserved nap…
Ok, so if you stuck with me thus far here are some pics. You decide… was it worth it?
Thanks for checking this out...